(Syllabus) Punjab PSC Mains Examination (Electrical Engineering)

Punjab Public Service Commission (PPSC)

Mains Examination Syllabus - Electrical Engineering

PAPER - I

1. Circuit Theory:

Circuit components; network graphs; KCL, KVL; circuit analysis methods : nodal analysis, mesh analysis; basic network theorems and applications; transient analysis : RL, RC and RLC circuits; sinusoidal steady state analysis; resonant circuits; coupled circuits; balanced 3-phase circuits; Two-port networks.

2. Signals & Systems:

Representation of continuous-time and discrete-time signals & systems; LTI systems; convolution ; impulse response; time-domain analysis of LTI systems based on convolution and differential/difference equations. Fourier transform, Laplace transform, Z-transform, Transfer function. Sampling and recovery of signals DFT, FFT Processing of analog signals through discrete-time systems.

3. E.M. Theory:

Maxwell’s equations, wave propagation in bounded media. Boundary conditions, reflection and refraction of plane waves. Transmission line: travelling and standing waves, impedance matching, Smith chart.

4. Analog Electronics:

Characteristics and equivalent circuits (large and small-signal) of Diode, BJT, JFET and MOSFET. Diode circuits : clipping, clamping, rectifier. Biasing and bias stability. FET amplifiers. Current mirror; Amplifiers: single and multi-stage, differential, operational, feedback and power. Analysis of amplifiers; frequency-response of amplifiers. OPAMP circuits. Filters; sinusoidal oscillators : criterion for oscillation; single-transistor and OPAMP configurations. Function generators and wave-shaping circuits. Linear and switching power supplies.

5. Digital Electronics:

Boolean algebra; minimization of Boolean functions; logic gates; digital IC families (DTL, TTL, ECL, MOS, CMOS). Combinational circuits : arithmetic circuits, code converters, multiplexers and decoders. Sequential circuits : latches and flip-flops, counters and shift-registers. Comparators, timers, multivibrators. Sample and hold circuits, ADCs and DACs. Semiconductor memories. Logic implementation using programmable devices (ROM, PLA, FPGA).

6. Energy Conversion:

Principles of electromechanical energy conversion : Torque and emf in rotating machines. DC machines : characteristics and performance analysis; starting and speed control of motors; Transformers : principles of operation and analysis; regulation, efficiency; 3- phase transformers. 3-phase induction machines and synchronous machines : characteristics and performance analysis; speed control.

7. Power Electronics and Electric Drives:

Semiconductor power devices : diode, transistor, thyristor, triac, GTO and MOSFET– static characteristics and principles of operation; triggering circuits; phase control rectifiers; bridge converters : fully-controlled and half-controlled; principles of thyristor choppers and inverters; DC-DC converters; Switch mode inverter; basic concepts of speed control of DC and AC motor drives applications of variable-speed drives.

8. Analog Communication:

Random variables : continuous, discrete; probability, probability functions. Statistical averages; probability models; Random signals and noise : white noise, noise equivalent bandwidth; signal transmission with noise; signal to noise ratio. Linear CW modulation : Amplitude modulation : DSB, DSB-SC and SSB. Modulators and Demodulators; Phase and Frequency modulation : PM & FM signals; narrowband FM; generation & detection of FM and PM, Deemphasis, Preemphasis. CW modulation system : Superhetrodyne receivers, AM receivers, communication receivers, FM receivers, phase locked loop, SSB receiver Signal to noise ratio calculation for AM and FM receivers.

PAPER - II

1. Control Systems :

Elements of control systems; block-diagram representation; open-loop & closed-loop systems; principles and applications of feed-back. Control system components. LTI systems : time-domain and transform-domain analysis. Stability : Routh Hurwitz criterion, root-loci, Bode-plots and polar plots, Nyquist’s criterion; Design of lead-lad compensators. Proportional, PI, PID controllers. State-variable representation and analysis of control systems.

2. Microprocessors and Microcomputers :

PC organisation; CPU, instruction set, register set, timing diagram, programming, interrupts, memory interfacing, I/O interfacing, programmable peripheral devices.

3. Measurement and Instrumentation :

Error analysis; measurement of current, voltage, power, energy, power-factor, resistance, inductance, capacitance and frequency; bridge measurement. Signal conditioning circuit; Electronic measuring instruments : multimeter, CRO, digital voltmeter, frequency counter, Q-meter, spectrum-analyzer, distortion-meter. Transducers : thermocouple, thermistor, LVDT, strain-gauge, piezo-electric crystal.

4. Power Systems: Analysis and Control :

Steady-state performance of overhead transmission lines and cables; principles of active and reactive power transfer and distribution; per-unit quantities; bus admittance and impedance matrices; load flow; voltage control and power factor correction; economic operation; symmetrical components, analysis of symmetrical and unsymmetrical faults. Concept of system stability: swing curves and equal area criterion. Static VAR system. Basic concepts of HVDC transmission.

5. Power System Protection :

Principles of overcurrent, differential and distance protection. Concept of solid state relays. Circuit breakers. Computer aided protection : Introduction; line bus, generator, transformer protection; numeric relays and application of DSP to protection.

6. Digital Communication :

Pulse code modulation (PCM), differential pulse code modulation (DPCM), delta modulation (DM), Digital modulation and demodulation schemes : amplitude, phase and frequency keying schemes (ASK, PSK, FSK). Error control coding : error detection and correction, linear block codes, convolution codes. Information measure and source coding. Data networks, 7-layer architecture.

Go Back To Main Page

Courtesy : ppsc.gov.in